Peet's Dystopian Shirt, Part 3 - Distressing

Peet's Dystopian Shirt, Part 2 - Sewing

Peet's Dystopian Shirt, Part 1 - The Mockup

Dave's Christmas Stocking

Dave's Christmas Stocking: A Story of Fitting In

Claymore Corsets (White Over-bust)

Photo by natendowli

AnimeNext 2008 two of my sisters, a friend, and I cosplayed characters from Claymore.

Backstory: AnimeNext is a NJ convention for anime and manga fans. Two of my sisters (C&S) and I have attended a few years. In 2008, we decided to make costumes of characters from Claymore, which seemed to lend themselves to corsets.

How I did it: I was intending to make corsets for each of the four of us, but ran out of time. The finishing work on one of the corsets was completed on site at the hotel on Friday night of the convention.

I made two corsets - one that mostly fit me and C, and the other that fit S and would be okay but not a great fit for the friend. Both were made using the Laughing Moon Dore pattern, with I believe a C-cup bust on the smaller and a D-cup bust on the larger (I could be wrong).

The corsets were made out of two layers of white foundation fabric (I forget exactly what, perhaps a cotton duck or herringbone twill) and a fashion layer of what is probably the worst fabric to try to put on a corset, a stretchy dance/swim fabric (which we were using for the two-piece bodysuits we wore beneath the corsets). I wanted to use the dance/swim fabric on the corset so that the pieces would look like they went together, but it was extremely hard to work with. I used the sandwich method previously mentioned and while the actual construction part went fine (as the stretchy fabric was sandwiched between the foundation layers) the top-stitching was a problem.

The smaller corset has a bone on each seam and mid-panel; the larger one has only bones on the seams. They are boned with steel. I did not use binding on the edge, as I had left a bit of extra fabric intending on stitching it down on the inside of the corset to draw less attention to the edge.

I also designed and made the bodysuit pieces, and my mom and C and S made the armor (vinyl) and spats. My sisters also made the claymore foam swords you see in the pictures.

What I learned: You can't treat the swim/dance fabric like normal fabric. There was a lot of issue with puckering. Also, I would have had a better fit all around if I had the time to do a mock-up for each of us (I had a mock-up for S, which is why the corset she and our friend wore fit her rather well; the other corset was done with just measurements for C and had upper edge gap issues).

What I might try next time: Mock-ups for everyone. Also, I would probably use the sandwich method, but fold over the foundation layers and sew the bone channels before folding the dance/swim fabric over to avoid doing any top-stitching on the dance/swim, which should smooth out the fabric and bring the corset closer to the look of the manga (less visible seams and stitching). I actually have the already-cut material and supplies to do the other two corsets, I just haven't gotten myself focused enough to sit down and do it.

Final Thoughts: Like most of my projects, I gave myself a very short time to complete this. I think considering the time restriction and the difference in vision between me and my mom and sisters the end product turned out pretty well.

Other Corset Posts:
My First Corset (Black mid-bust)
The Do-Everything Corset (Black under-bust)
Rikku/Steampunk Corset (Green mid-bust)
Old Pants Deconstructed Corset (Tan under-bust)

The Do-Everything Corset (Black Under-bust)

I made this black under-bust corset for a costume, but it's gotten so much more use than just one costume. I wear it to dress up for a special occasion, I wear it out to the goth club, I wear it for other costumes.

Backstory: Halloween, 2007. We were going to a costume party and I decided to make our costumes to a theme - drinking (since that's what most people do at those parties anyway). I made my husband a pirate coat and he went as Captain Morgan. I made myself this corset and went as the St. Pauli Girl.

How I did it: I made a mock-up out of muslin and heavy-duty cable ties using the Laughing Moon Dore pattern. I drew the basic shape of the corset on the mockup and then cut it down and tried it back on. Once I was pleased with the shaping of the top edge I transferred that shape to the pattern and cut it out of the same black moleskin suede I used for the first corset I made. I also cut out a lining of black fabric.

I sewed it together using the method described by another corsetmaker here, except that I had to do some creative finagling with the final seam as I made it a closed back. I stitched bone channels on each seam and midway through each panel, with a channel on either side of the center back seam. I boned the entire thing in heavy-duty cable ties, because they are easy to get at the home improvement store, are fairly flexible, and I was on a short time frame when making this so I didn't have the time to order spiral and flat steel bones. I applied the binding in a quick-and-dirty way, machine sewing it to the inside, folding it over to the outside, and machine stitching close to the edge. The grommets were applied by hand, using a grommet set and mallet.

What I learned: I can make a corset in a very short time frame that looks pretty good and holds up to the test of several hours of wear and dancing in the club.

What I might try next time: I would like to make another under-bust with steel boning.

Final Thoughts: This corset has lasted almost five years, countless club nights, being worn for hours at a time... Awesome!

 

Other Corset Posts:
My First Corset (Black Mid-bust)
Claymore Corsets (White over-bust)
Rikku/Steampunk Corset (Green mid-bust)
Old Pants Deconstructed Corset (Tan under-bust)

My First Corset (Black Mid-bust)

In 2007 I decided to make myself a corset. (This is my sister wearing it - she looks great!)

Backstory: At some point when I joined livejournal I stumbled upon the corsetmakers community. Being inspired by all the amazing things they made, I decided to get myself a kit and some fabric and give it a go.

How I did it: I bought the Laughing Moon Dore/Silverado corset pattern (after reading about different patterns on corsetmaking on LJ) and a corset kit (with boning, grommets, lacing, etc.) from corsetmaking.com. I had some beautiful black fabric (moleskin suede or miscrosuede, I think) and wanted to make a classic black corset.

I made a mock-up from white muslin and the boning and busk (front closure) from the kit. I did the mock-up in a size 14, I believe with the b-cup bust shaping. The mock-up closed all the way in the back, so I decided to take off two inches for the final version. One thing I did not consider when deciding what to do with the size for the final version was that one layer of muslin was going to have a lot more give than what ended up being three layers (a skull bandanna print fashion cotton lining, the strength layer cotton drill, and the moleskin suede exterior).

For the final version, I sewed the outside layer as one layer, and the lining and strength layer together as another, then pinned the layers together and stitched through all three layers of fabric, following the directions included with the pattern. I stitched the bone casings and inserted the bones between the layers. Then I applied binding to the top and bottom edges, sewing by machine on the outside and hand stitching on the inside. The grommets were applied by hand.

What I learned: As I mentioned above, one layer of fabric does different things than three. Additionally, sewing the outside and inside separately and then trying to line everything up is a giant PITA. After I completed this I switched my method to sewing all the layers together on each seam, using the method outlined by another corsetmaker here. Since this corset ended up being too small and a touch too short, I sold it online.

What I might try next time: I've made a few other corsets since this one, using the sewing method above and generally only two layers of fabric. I haven't gotten around to making myself another mid-bust (or overbust) black corset, but I'd like to eventually recreate this in a better fit with a little length added.

Final Thoughts: This was my first real corset (I made a corset-like item for my sister previous to this). It turned out pretty nicely, and hopefully went on to a full life in its new home.

Other Corset Posts:
My First Corset (Black mid-bust)
The Do-Everything Corset (Black under-bust)
Claymore Corsets (White over-bust)
Rikku/Steampunk Corset (Green mid-bust)
Old Pants Deconstructed Corset (Tan under-bust)

Flashback: Wall Hangings

Years ago, I made wall hangings as Christmas presents for a few of our friends. I don't have pictures of them all, but here's a little info on what I did.

Swampy Outfit

This was a costume for my husband for a dystopian zombie LARP. If you don't know what a LARP is, read on.